Mazda 626

1991-1998 of release

Repair and operation of the car

Mazda 626

+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   - 3.1. Petrol engines (1,6 and 1,8 liters)
      3.1.1. Introduction
      3.1.2. Technical characteristics
      3.1.3. Recommendations about repair
      3.1.4. Top dead point
      3.1.5. Cover of valves
      3.1.6. Inlet collector
      3.1.7. Final collector
      3.1.8. Gas-distributing belt and asterisks
      3.1.9. Camshaft epiploons
      3.1.10. Yokes and distributive shaft
      3.1.11. Springs of valves, fastenings and laying
      3.1.12. Head of cylinders
      3.1.13. Oil pallet
      3.1.14. Forward cover
      3.1.15. Oil pump
      3.1.16. Forward epiploon of a bent shaft
      3.1.17. Flywheel
      3.1.18. Back epiploon of a bent shaft
      3.1.19. Fastenings of the engine
   + 3.2. Petrol 4-cylinder engine (2 liters)
   + 3.3. Petrol V6 engine (2,5 liters)
   + 3.4. Partition of engines (1,6 and 1,8 liters)
   + 3.5. Partition of engines (2,0 and 2,5 liters of V6)
   + 3.6. Diesel engine 2,0 liters
   + 3.7. Systems of electric equipment of the engine
+ 4. Heating and ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Running gear
+ 11. Body
+ 12. Electric equipment
+ 13. Electrical circuitries
+ 14. Useful tips

3.1.13. Oil pallet

Removal

PERFORMANCE ORDER

1. Disconnect a wire of the minus plug of the accumulator.
2. Lift and fix a forward part of the car.
	3. Remove protective guards of the engine.
4. Merge engine oil and remove an oil filter.
	5. Unscrew bolts of connection of an exhaust pipe.
	6. Disconnect an exhaust pipe from a final collector.
7. The oil pallet can consist of one or of two parts.
	8. If the pallet consists of two parts, unscrew bolts in a back part of the transmission and a case of the engine and remove a back part of the pallet. Unscrew the remained bolts and remove the pallet.
	9. Disconnect a maslozaborny branch pipe from the block of covers of radical bearings and remove it.
	10. Unscrew bolts of the block of covers.
	11. Remove the block of covers.

Installation

PERFORMANCE ORDER

1. Clean the joined surfaces of the block of covers, the oil pallet and the block of cylinders.
2. Examine the pallet, a maslozaborny branch pipe and carvings of openings of bolts.
	3. In all models apply silicone sealant on the shaded surfaces of the block of cylinders.
	4. In all models apply silicone sealant on the joined surface of the block of covers. Insert bolts of the block and tighten them.
5. In models apply silicone sealant on the joined surface of the oil pallet. Insert bolts of the pallet and tighten them.
	6. In all models apply silicone sealant on new laying of the oil pump and a back cover. Establish laying. Apply silicone sealant on the joined surface of the oil pallet, install the oil pallet and tighten fixing bolts.
7. Establish the remained details.
8. Wait 12 hours that silicone sealant hardened, and check operation of the engine.

home