Mazda 626

1991-1998 of release

Repair and operation of the car



Mazda 626

+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. Petrol engines (1,6 and 1,8 liters)
   + 3.2. Petrol 4-cylinder engine (2 liters)
   + 3.3. Petrol V6 engine (2,5 liters)
   + 3.4. Partition of engines (1,6 and 1,8 liters)
   - 3.5. Partition of engines (2,0 and 2,5 liters of V6)
      3.5.1. Introduction
      + 3.5.2. Technical characteristics
      3.5.3. Repair work without dismantle of the engine from the car
      + 3.5.4. Capital repairs of the engine
      3.5.5. Check by means of the vacuum measuring instrument
      3.5.6. Check of a compression
      3.5.7. Methods of dismantle of the engine
      3.5.8. Removal and installation of the engine
      3.5.9. Engine partition
      3.5.10. Partition and check of a head of cylinders
      3.5.11. Valves
      3.5.12. Assembly of a head of cylinders
      3.5.13. Removal of pistons and rods
      3.5.14. Removal of a bent shaft
      3.5.15. Check of the block of cylinders
      3.5.16. Honingovaniye of cylinders
      3.5.17. Check of pistons and rods
      3.5.18. Check of a bent shaft
      3.5.19. Check and selection of radical bearings and bearings of rods
      3.5.20. Check of camshafts and pushers
      3.5.21. Engine assembly order
      3.5.22. Installation of piston rings
      3.5.23. Installation of a bent shaft
      3.5.24. Installation of a back epiploon of a bent shaft
      3.5.25. Installation of pistons and rods
   + 3.6. Diesel engine 2,0 liters
   + 3.7. Systems of electric equipment of the engine
+ 4. Heating and ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Running gear
+ 11. Body
+ 12. Electric equipment
+ 13. Electrical circuitries
+ 14. Useful tips


4295d568



3.5.3. Repair work without dismantle of the engine from the car

GENERAL INFORMATION

Without dismantle of the engine from the car it is possible to execute a set of the main operations on repair.

Before any works it is very desirable to wash out a motor compartment and the engine a water stream. It is easier to work with the pure engine, pollution of the internal device of the engine is prevented.

To expand working space and not to damage coloring, uncover a motor compartment and hinged mudguards.

If traces of the leaks of oil or cooling liquid indicating replacements of laying the need are observed, then all works as a rule are carried out without dismantle of the engine. Without dismantle it is possible to replace laying of the oil pallet, a head of the block of cylinders, laying of inlet and final collectors, forward and back covers, an epiploon of a bent shaft.

Without dismantle of the engine it is also possible to remove such hinged units as the pump of cooling liquid, a starter, the generator, the ignition distributor, inlet and final collectors, and also the fuel pump and the carburetor.

As the head of the block of cylinders can be removed without dismantle of the engine too, also repair of the valvate mechanism is possible.

Without dismantle it is also possible to perform such works as replacement or check of a condition of a gear belt, gear wheels of the drive of a cam-shaft, the oil pump, consolidation of a forward cover.

In extreme cases when there is no necessary equipment, without removal of the engine it is possible to replace piston rings, pistons, rods and connecting rods, to otkhonningovat cylinders. However, it is not recommended to perform these works without removal of the engine as cleaning of the accompanying details and preparatory activities are required.

In the corresponding chapters of this manual actions for dismantle, check and installation of the units stated above are in detail described.


On the homepage